Roof Curbs - 8 inch Tall

Roof Curb for Mounting Curb Mount Flange Vents and Fans
Roof Curb available with matching roof cap

AVP's Roof Curbs fit Roof Vents and Exhaust Fans with a Curb Mount Flange

A roof curb is a box that acts as an extension from the roof deck. This extension provides a base for a roof vent or exhaust fan. These roof curbs are intended for flat roofs only.

AVP’s Roof Curbs are made from aluminum and are offered in 4 height options. For climates with moderate snow, an 8 inch tall roof curb is ideal.

An important reason for the use of a curb is a roofing manufacturer's warranty. Many EPDM, PVC & TPO roofing manufacturers require roofing penetrations to be secured by a curb and a boot. Check with your roofing materials supplier to purchase a boot that slides over the aluminum curb.

The boot provides a factory-approved attachment to the roof deck’s membrane. The upper end of the boot folds into the curb. Then the curb mount flange goes over both the boot and curb. This will provide a perfect seal from the top.

Outside Length

Inside Opening

6"5"8"For a 3" Diameter Vent or FanRC-3-H8
7"6"8"For a 4" Diameter Vent or FanRC-4-H8
8"7"8"For a 5" Diameter Vent or FanRC-5-H8
9"8"8"For a 6" Diameter Vent or FanRC-6-H8
10"9"8"For a 7" Diameter Vent or FanRC-7-H8
11"10"8"For an 8" Diameter Vent or FanRC-8-H8
12"11"8"For a 9" Diameter Vent or FanRC-9-H18
13"12"8"For a 10" Diameter Vent or FanRC-10-H8

Outside Length

Inside Opening

15"13"8"For a 12" Diameter Vent or FanRC-12-H8
17"15"8"For a 14" Diameter Vent or FanRC-14-H8
19"17"8"For a 16" Diameter Vent or FanRC-16-H8
21"19"8"For an 18" Diameter Vent or FanRC-18-H8
23"21"8"For a 20" Diameter Vent or FanRC-20-H8
27"25"8"For a 24" Diameter Vent or FanRC-24-H8
33"31"8"For a 30" Diameter Vent or FanRC-30-H8
39"37"8"For a 36" Diameter Vent or FanRC-36-H8
45"43"8"For a 42" Diameter Vent or FanRC-42-H8
51"49"8"For a 48" Diameter Vent or FanRC-48-H8


An additional benefit to using an 8 inch tall roof curb is it can act as a hatch or access entry port. The roof vent or exhaust fan can be easily removed. As a result, allowing for quick access to ductwork, electrical lines, or maintenance in the attic below.

Traditionally, roofers build wooden boxes on the roof at the time of the membrane installation. Using prefabricated aluminum curbs reduces the time and need to build wooden boxes. This will also lower the risk of injury during installation by lowing the time spent on the roof. In addition, any chances to damage the roof in the building process are also lower.

Another safety feature is that aluminum curbs are not flammable. The majority of curbs vent out heat from range hoods or HVAC units. This can cause wooden curbs to burn. However, aluminum will not burn, rust, or corrode. Aluminum curbs are safer and easy to clean.

For any questions, please email the sales team at [email protected] or call 845-565-7770.

Shop roof curbs on AVP’s website:

Copyright Active Ventilation Products, Inc. 2021 - All Rights Reserved
linkedin facebook pinterest youtube rss twitter instagram facebook-blank rss-blank linkedin-blank pinterest youtube twitter instagram